Valspar Premium Masonry Exterior Wall & ceiling Basecoat, Base 2, 236ml Tester pot Picasso Blue R146B
Product Features
- Self-cleaning
- Microporous & Breathable
- Showerproof in 30 minutes
How much will I need?
Product details
Product information
Product information
Test out your favourite Valspar colours at home – this sample has a smooth finish and is suitable for almost any exterior stone surfaces. Valspar® Premium Masonry features a microporous film, making it breathable and tough for long term protection. It’s showerproof in just 30 minutes and can be applied to damp surfaces. Valspar® Premium Masonry also has built in self-cleaning technology and is UV resistant so it won’t crack, blister or peel, ensuring your surface is protected against harsh weather conditions.
- Stain resistant
- Scrubbable
- Suitable for Masonry
- Surface Preparation - The surface must be clean, dry and free of dirt, chalk and grime. Glossy surfaces should be lightly sanded before painting. Repair all damaged areas. Lightly sand old, loose or flaky paint. If mould, moss, algae or lichen are present, they must be completely removed. Apply a solution of 1 part bleach and 3 parts water. Rinse thoroughly. We recommend to seal absorbent surfaces with an Exterior Primer & Undercoat.
- Instructions for Use - Stir contents to ensure paint is thoroughly mixed. Purchase enough paint to complete the job. When purchasing more than one container of the same colour, intermix containers to ensure colour uniformity. If you feel that you may run out of paint, stop at a corner or a natural break. Apply 1–2 coats using a suitable brush, roller or sprayer. Apply liberally, working from dry areas into the paint’s wet edge and finish with gentle, vertical strokes. Avoid excessive rolling or brushing. Extra coats may be required when making dramatic colour changes. Do not thin this product. Dries to the touch in about 1 hour under normal conditions. Allow 2-4 hours between coats.
Features and benefits
- Self-cleaning
- Microporous & Breathable
- Showerproof in 30 minutes
- Long-lasting Colour
- We’re unable to offer refunds or to exchange products that have been mixed to your individual requirements. If the product you purchase is faulty, or not as described, we may offer an exchange, refund or repair as appropriate. This does not affect your legal rights.
Health and safety
Please note that this item has additional safety or regulatory datasheets available. The product may have possible health and safety hazards covered in these documents. Refer to the container for full information and always follow the instructions.
Specifications
| Brand | Valspar |
|---|---|
| Application method | Brush, roller or spray |
| Base | Water-based |
| Coverage | 2.36m² |
| Drying time | 30 min |
| Location | Exterior |
| Maximum application temperature | 25°C |
| Minimum application temperature | 10°C |
| Minimum touch dry time | 0.5h |
| Number of coats | 2 |
| Recoat time | 4 hours |
| VOC level | Minimal |
| Volume | 236ml |
| Product code | 5055018189488 |
Documents
Product Guide
Safety Information
Read carefully and follow all instructions. Keep out of reach of children. If medical advice is needed, have product container or label at hand. Contains a biocidal product. Contains 1,2-benzisothiazol-3(2H)-one and reaction mass of 5-chloro-2-methyl-2H-isothiazol- 3-one and 2-methyl-2H-isothiazol-3-one (3:1). May produce an allergic reaction. Warning! Hazardous respirable droplets may be formed when sprayed. Do not breathe spray or mist.
Ensure good ventilation during application and drying. When applying it is advisable to wear eye protection. Avoid inhaltion of dust. Wear a face mask if dry sanding.
Contains a biocidal product for the preservation of the dry film: 3-iodo-2-propynyl butylcarbamate (IPBC) & Terbutryn.
Manufacturer / EU responsible person
EU responsible person
Sherwin-Williams (Ireland) Ltd
Address
Unit 53
Robinhood Industrial Estate
Dublin 22
D22PW99
Ireland